Emulex NQTR0V-NATM Manuel d'utilisateur

User Guide for Emulex Printer Servers Version 5.0 ER2054618-00A

Table of Contents viii APPENDIX CONNECTOR PINOUTS ...A-ERROR! BOOKMARK NOT DEFINED. ETHERNET UTP CONNECTOR PINOUT - RJ-45 ...

3-18 Chapter 3 Define the Preferred Novell NetWare File Server Upon power up, the Emulex printer server normally goes through fileservers in the bin

Novell NetWare 3-19 Define the NDS tree Sites with multiple NDS trees can specify which NDS tree the printer server will attach to and scan for se

3-20 Chapter 3 What’s Next? After a successful configuration of your network operating system, you can either configure for another NOS or manage yo

UNIX TCP/IP Chapter 4 REQUIREMENTS ...4-1

UNIX TCP/IP 4-1 Requirements Before beginning, verify the network conforms to these requirements: • Clients must support TCP/IP, TELNET, UDP

4-2 Chapter 4 * Pre-compiled binaries for these system types are included on the distribution media, the distribution files do not need to be comp

UNIX TCP/IP 4-3 mount_point The directory path mount point for the CD-ROM drive. The tar command creates a subdirectory called emlx under the

4-4 Chapter 4 When the ENSTALL utility begins, follow the instructions and supply the requested information. When the ENSTALL program is complete

UNIX TCP/IP 4-5 Assign IP Address 1) Login to the UNIX host as root user. 2) Verify IP address availability. > #ping IP_address IP_addres

4-6 Chapter 4 5) Enter: > #ping IP_address IP_address The printer server IP address in decimal dot notation. NOTE: The command interrupt ke

Introduction Chapter 1 Thank you for purchasing an Emulex network product. You have joined the Emulex family of users who have found that our prod

UNIX TCP/IP 4-7 BootP Emulex printer servers will accept and configure the following parameters from a TCP/IP BootP server host: • Gateway IP

4-8 Chapter 4 4) Enter Emulex printer server command: > Server>> define server bootp n m [temp] n The number of times to request BootP

UNIX TCP/IP 4-9 When the Emulex printer server reboots, the default sequence of IP address acquisition is to attempt BootP first; if BootP fai

4-10 Chapter 4 When the printer server is booted, the host receives the RARP request from the printer server. It then sends the IP address in the

UNIX TCP/IP 4-11 3) Edit the file ENVIRON.H to reflect the appropriate system type. Typical system parameters for Sun Sparc Stations are: &g

4-12 Chapter 4 6) Create a directory for the spooled files: > #mkdir /usr/spool/printer_name > #chown daemon /usr/spool/printer_name >

UNIX TCP/IP 4-13 Configure a System V Host 1) Copy the Emulex utility RPRINT.C to a host system. This file is found on the UNIX utilities di

4-14 Chapter 4 For example, the following defines a LaserJet IIIsi printer named emlx_txt on the parallel port (port 1, TCP port 2501): > #eml

UNIX TCP/IP 4-15 > #/usr/lib/lpadmin -pemlx -v/dev/null -i/user/emlx/lp_emlx > #/usr/lib/lpsched (HP-UX only) > #/usr/lib/accept

4-16 Chapter 4 LPD In most cases, local print options such as header and trailer banner pages, and input or output filters are ignored. If this l

1-2 Chapter 1 − Configure printer servers - For example, add printers, assign trap hosts, assign workgroups, upgrade printer server software, perfo

UNIX TCP/IP 4-17 For sending PostScript or graphics files to port 1: > LJ4_PS|HP_LaserJet_4|port_1:\ :lp=:\ :rm=node_name:\ :rp=PASSTHR

4-18 Chapter 4 4) Add the server’s node_name to the /etc/hosts file. For example: > #IP_address node_name IP_address The printer server

UNIX TCP/IP 4-19 LPSTAT Use LPSTAT to determine the current status of a printer connected to the printer server. From any host terminal: 1)

4-20 Chapter 4 Events reported for an MIO printer interface, with the Syslog severity/priority shown in parentheses: − Load paper (warning) − Me

UNIX TCP/IP 4-21 3) Configure a host as a syslog server: > Server>> define node node_name name IP IP_address syslog facility node_n

4-22 Chapter 4 3) Enter the password: > #access where access is the default printer server remote login password. NOTE: The password does not

UNIX TCP/IP 4-23 Local Login 1) Connect an ANSII compatible terminal or a PC running an ANSII terminal emulation program to the printer serve

4-24 Chapter 4 What’s Next? Upon successful configuration of your network operating system, you can either configure for another NOS or manage you

VAX/VMS DECnet LAT Chapter 5 REQUIREMENTS ...

VAX/VMS DECnet LAT 5-1 Requirements Before beginning, verify the network meets this requirement: Clients must support the LAT protocol under the

Introduction 1-3 Check Media You have received software either on CD-ROM or diskette. Depending upon the media enclosed, verify the contents: C

5-2 Chapter 5 > LATCP> set port lta901:/application/node= server_name /port=port_n server_name The Emulex default server name from the Befo

VAX/VMS DECnet LAT 5-3 Logging into the Printer Server You can login to the printer server remotely from a DEC workstation using the VAX NCP uti

5-4 Chapter 5 9) At Server>, enter su: > Server> su This gives you supervisor status. 10) At Password>, enter system: > Password&

VAX/VMS DECnet LAT 5-5 where system is the default privileged password which does not echo back. 7) At the Server>> prompt, view or chang

5-6 Chapter 5 What’s Next? Upon successful configuration of your network operating system, you can either configure for another NOS or manage your

AppleTalk Chapter 6 REQUIREMENTS ...6-1

AppleTalk 6-1 Requirements Before beginning, verify the network conforms to these requirements: • AppleTalk Phase 2 • System 6 or System 7 • La

6-2 Chapter 6 Logging into the Printer Server You can login to the printer server remotely from a UNIX workstation or locally from a console termi

AppleTalk 6-3 9) Logout of the printer server: > Server>> logout Local Login 1) Connect an ANSII compatible terminal or a PC running an

6-4 Chapter 6 Advanced AppleTalk Parameters IMPORTANT: This section contains advanced features. All parameters should be configured by the Networ

1-4 Chapter 1 How to Use This Guide This guide is designed to assist in the installation of your Emulex printer server. The material contained in t

AppleTalk 6-5 View Printer Fonts NOTE: Spelling and capitalization of the fonts must be entered exactly as required by the printer. View fonts su

6-6 Chapter 6 Remove Printer Server Fonts To remove one or more font strings from one or more port’s font list, enter: > Server>> change

AppleTalk 6-7 What’s Next? Upon successful configuration of your network operating system, you can either configure for another NOS or manage your

LAN Manager Chapter 7 REQUIREMENTS ...

Lan Manager 7-1 Requirements Before beginning, verify the network conforms to these requirements: • Microsoft LAN Manager version 2.1 or higher

7-2 Chapter 7 NOTE: In order to print using the NetBios protocol, the user must logon to the server’s domain. Add the “logon/D:domain” command bef

Lan Manager 7-3 Before Installation We recommend writing down the following parameters from the Setup Section in Chapter 2. Refer to them durin

7-4 Chapter 7 SOCKDRV.OS2 Verify the file SOCKDRV.OS2 is installed using the OS/2 System Editor. 1) Examine CONFIG.SYS in the LAN Manager root dire

Lan Manager 7-5 Add New Printers Before adding printers, install the required printer drivers through the OS/2 Print Manager. 1) Double-click o

7-6 Chapter 7 5) Choose either TCP/IP or NETBIOS. Continue installation by referring to either the following TCP/IP or the NetBios section. TCP/IP

Introduction 1-5 Variables Variables are used as in mathematics: they represent a quantity, device name, address or other entity. They are show

Lan Manager 7-7 3) Enter COMMENT. This optional information is used to further define a print queue. It is shown in the remark field when the

7-8 Chapter 7 Advanced Options Modify or select other options. Trace Mode Enabling this option is not recommended. However, if enabled, debugging

Lan Manager 7-9 NetBios Protocol From the ADD NEW NETBIOS PRINTER window: Figure 7-6: Add New NetBios Printer Window 1) Enter Name. Enter a m

7-10 Chapter 7 NOTE: To add additional drivers to the Emulex print manager driver list, install a new printer under the OS/2 Print Manager and sele

Lan Manager 7-11 1) Select desired options. 2) Click OK. This returns the user to the ADD NEW PRINTER window. 3) Click ADD. The printer is n

7-12 Chapter 7 Change or Delete Printers From the DESKTOP MANAGER GROUP: 1) Open the EMULEX PRINT MANAGER. 2) Select the EMULEX PRINT MANAGER icon

Lan Manager 7-13 Figure 7-8: Change TCP/IP RPRINT Printer’s Properties Window 4) Change the SERVICE NAME or IP ADDRESS. 5) Click MORE>>

7-14 Chapter 7 The CHANGE NETBIOS PRINTER’S PROPERTIES window is displayed. Figure 7-9: Change NetBios Printer’s Properties Window 4) Change the

Lan Manager 7-15 TELRCFThe TELRCF utility may be used to login to the printer server from the LAN Manager server and to issue server commands. F

7-16 Chapter 7 10) Enter desired TELRCF options in the Parameters box. Available options: -h server_name or ip_address -p rcf_tcp_port_number (

1-6 Chapter 1 NOS & Protocol Support With the recent release of printer server software version 5.0, we have expanded the protocols supported by

Lan Manager 7-17 Enter Scripts TELRCF provides a convenient method for downloading an entire configuration script to the printer server. A samp

7-18 Chapter 7 What’s Next? Upon successful configuration of your network operating system, you can either configure for another NOS or manage your

LAN Server Chapter 8 REQUIREMENTS ...8

LAN Server 8-1 Requirements Before beginning, verify the network conforms to these requirements: • IBM LAN Server version 3.0 or higher • IBM

8-2 Chapter 8 NOTE: In order to print using the NetBios protocol, the user must logon to the server’s domain. Add the “logon/D:domain” command bef

LAN Server 8-3 Before Installation We recommend writing down the following parameters from the Setup Section in Chapter 2. Refer to them during

8-4 Chapter 8 LAN Server 4.0 To configure printers to be shared on the network, login to the LAN Server as admin and verify setup. Verify the networ

LAN Server 8-5 Add New Printers Before adding printers, the appropriate printer drivers must be installed through the OS/2 Print Manager. 1) Do

8-6 Chapter 8 TCP/IP Protocol From the ADD NEW TCP/IP RPRINT PRINTER window: Figure 8-3: TCP/IP Add New Printer Window 1) Enter Name. Enter at l

LAN Server 8-7 NOTE: To add additional drivers to the Emulex print manager driver list, install a new printer under the OS/2 Print Manager and

Printer Server Installation Chapter 2 NETJET ...

8-8 Chapter 8 Advanced Options Modify or select other options. Trace Mode Enabling this option is not recommended. However, if enabled, debugging

LAN Server 8-9 NetBios Protocol From the ADD NEW NETBIOS PRINTER window: Figure 8-5: NetBios Add New Printer Window 1) Enter Name. Enter a m

8-10 Chapter 8 4) Choose Driver. Select the printer driver to be used for this printer. Use IMBNULL if the files do not require formatting (for ex

LAN Server 8-11 Trace Mode Enabling this option is not recommended. However, if enabled, debugging information is sent to RPRINTNB.EXE stdout.

8-12 Chapter 8 From the NETBIOS ADVANCED OPTIONS window: 1) Select desired options. 2) Click OK. This returns the user to the ADD NEW PRINTER wi

LAN Server 8-13 Change or Delete Printers From the DESKTOP MANAGER GROUP: 1) Open the EMULEX PRINT MANAGER. 2) Select the EMULEX PRINT MANAGER

8-14 Chapter 8 Change NetBios Printer’s Properties If you have chosen a NetBios Protocol printer to be changed, the following screen will be display

LAN Server 8-15 Options Menu The following Options may be accessed from the OPTIONS menu in the EMULEX PRINT MANAGER. 1) Pull down OPTIONS from

8-16 Chapter 8 Configure TELRCF Although the TELRCF utility is automatically installed with other LAN Server files, it must be configured prior to u

LAN Server 8-17 Use TELRCFTELRCF may be used to login to the printer server to issue configuration commands. In addition, TELRCF provides a con

ii Chapter 2 PRINT TEST PAGE ...2-19 PRINT C

8-18 Chapter 8 The following is an example of a server command script. This command configures a new service name (for example, 1j4a), for remote p

LAN Server 8-19 What’s Next? Upon successful configuration of your network operating system, you can either configure for another NOS or manage

Windows NT Chapter 9 REQUIREMENTS ...9

Windows NT 9-1 Requirements Before beginning, make sure the network conforms to these requirements: • Version 3.5 of Windows NT is the minimum ve

9-2 Chapter 9 Assigning an IP Address You must assign an IP address prior to installing with Windows NT. DHCP If the UNIX host is configured as a

Windows NT 9-3 Without DHCP 1) Login to the Emulex printer server. Refer to the Remote Login or Local Login section later in this chapter. 2) En

9-4 Chapter 9 NOTE: If the Enable Automatic DHCP Configuration option is not checked in the Installation Options dialog box, all required procedu

Windows NT 9-5 This opens the CREATE PRINTER dialog box: Figure 9-1: Create Printer Menu 2) Enter a name in the Printer Name box. This name can

9-6 Chapter 9 This displays the Print Destinations dialog box: Figure 9-2: Available Print Monitors List 5) Select LPR PORT. 6) Click OK. The

Windows NT 9-7 NOTE: LPR stands for Line Printing Utility, and LPD stands for Line Printing Daemon, which is how these elements are known on UNIX

Printer Server Installation iii NETQUE TOKEN RING...

9-8 Chapter 9 2) Enter: > Server>> change service lpd port all disable > Server>> change service printer_name TCP_port_n PORT

Windows NT 9-9 Figure 9-4: Create Printer 5) Enter a Share Name. This name can contain a maximum of eight characters. A default shared resource

9-10 Chapter 9 In PRINT MANAGER, the printer name specified in the CREATE PRINTER dialog box appears in the title bar of the printer’s window, as

Windows NT 9-11 There are two different ways to start or stop the LPDSVC service. At the command prompt: 1) Type net start LPDSVC or net stop LP

9-12 Chapter 9 2048 The printer server RCF port 3) Enter the password: > # access where access is the default printer server remote login pas

Windows NT 9-13 2) Press ESC twice. This initiates communication between the console terminal and the printer server serial port. 3) Verify ban

9-14 Chapter 9 What’s Next? Upon successful configuration of your network operating system, you can either configure for another NOS or manage you

Appendix Appendix CONNECTOR PINOUTS ...A-1 ETHERNET

Appendix A-1 Connector Pinouts Emulex printer server models have different configurations of input and output ports. Verify your Emulex printer serve

A-2 Appendix Token Ring STP Pinout - Female-DB9 − NETQue Token Ring 1 Receive /R1 2 No Connection 3 No Connection 4 No Connection 5 Transmit/B5 6 R

Information contained in this document is believed to be accurate and reliable. However, Emulex Corporation assumes no responsibility for its use nor

Appendix A-3 Console Connector Pinout - RJ12 (DTE) − NETJet 1 DTR Data Terminal Ready 2 TXD Transmit Data 3 GND Ground 4 RXC Receive Data Common 5 R

A-4 Appendix Parallel Connector Pinout − NETQue − NETQue Pro2 − NETQue Token Ring NOTE: This pinout must be maintained for bi-directional printin

Acronyms ARP Address resolution protocol. BootP A protocol used by a node to obtain its configuration from a host. BSD Berkeley Software Distrib

A-6 Appendix Pserver Novell Netware software utility that manages the operation of printers on the network. RARP Reverse Address Resolution Protocol

Glossary # Symbol used for default login password prompt on an RCF port. 10base2 Coaxial cable used to provide connectivity on a network; often refe

A-8 Appendix Coaxial A type of cable that uses two conductors; can accommodate high bandwidth and is relatively resistant to interference. Ethernet

Glossary A-9 Postscript Printer technology in which fonts are outline coded, fully scalable and permanently stored in ROM. These fonts may be downl

A-10 Appendix TCP/IP Transmission Control Protocol/Internet Protocol; a UNIX based protocol suite developed by the Advanced Research Projects Agency

Printer Server Installation 2-1 NETJet Reference Numbers It is important that you make a note of the printer server’s unique ethernet address (kno

2-2 Chapter 2 The default printer server name is very important and is always used when installing the printer server for the first time. Once a s

Printer Server Installation 2-3 7) Gently press the board into position. 8) Tighten the two captive screws. The captive screws are located on th

2-4 Chapter 2 Thinwire BNC Connection CAUTION: Do not break the ethernet connection while LAN is active. 1) If connecting to the middle of a cab

Printer Server Installation 2-5 Peripheral Connection Console/Serial PortMAC ADDRESS00-00-C9-01-A0-6ANETJetCONSOLE UTP 1 2 BNC Figure 2-5: Periph

2-6 Chapter 2 Power Up 1) Verify Emulex printer server is securely seated in printer slot. 2) Verify LAN connection to the printer server is sec

Printer Server Installation 2-7 Print Test Pagearameters The test pageparameter printout is a useful tool that can be used to verify the connect

2-8 Chapter 2 Reset to Factory Defaults Before resetting to factory defaults, we recommend that you print out a configuration page. Using the com

Printer Server Installation 2-9 Factory Default Configuration Parameter Default Setting Passwords system (privilege mode) access (remote login) P

Table of Contents CHAPTER 1 INTRODUCTION DOCUMENTATION ...1-

2-10 Chapter 2 Printer Server Specifications Parameter Range Ethernet Compatibility IEEE802.3, IEEE802.2, Ethernet Type 2 10base2, Thinwire (BNC)

Printer Server Installation 2-11 Declaration of Conformity This Declaration identifies the product, manufacturer’s name and address, and applicabl

2-12 Chapter 2 What’s Next? After successfully installing your Emulex printer server, you must configure the network operating system (NOS). Refe

Printer Server Installation 2-13 NETQue Pro2 Reference Numbers It is important that you make a note of the printer server’s unique ethernet addre

2-14 Chapter 2 To determine the default printer name, enter the Emulex default printer server name combined with the Emulex printer server port nu

Printer Server Installation 2-15 Thinwire BNC Connection CAUTION: Do not break the ethernet connection while LAN is active. 1) If connecting to

2-16 Chapter 2 Peripheral Connections Parallel Ports The parallel ports provide female DB25 connectors and support the following types of peripher

Printer Server Installation 2-17 NOTE: Serial cable between the printer server and the peripheral device or console terminal should not exceed 50

2-18 Chapter 2 Display Lights (LEDs) 1) When the printer server is powered up, the green POWER LED and the yellow PORT LED will illuminate. 2) W

Printer Server Installation 2-19 Print Test Page The test page is a helpful tool that can be used to verify the connection between the printer se

Table of Contents ii NETQUE PRO2 ... 2-13 REFERENCE NUMBERS

2-20 Chapter 2 Print Configuration Parameters Starting with software release 4.15, two methods can be used for printing configuration parameters.

Printer Server Installation 2-21 Reset to Factory Defaults Before resetting to factory defaults, we recommend that you print out a configuration p

2-22 Chapter 2 Factory Default Configuration Parameter Default Setting Passwords system (privilege mode) access (remote login) Printer server nam

Printer Server Installation 2-23 Printer Server Specifications Parameter Range Ethernet Compatibility IEEE802.3, IEEE802.2, Ethernet Type 2 10ba

2-24 Chapter 2 Declaration of Conformity This equipment complies with CISPR22/EN55022 Class A. WARNING: This is a class A product. In a domestic

Printer Server Installation 2-25 What’s Next? After successfully installing your Emulex printer server, you must configure the network operating s

2-26 Chapter 2 NETQue Reference Numbers It is important that you make a note of the printer server’s unique ethernet address (known as the Media A

Printer Server Installation 2-27 To determine the default printer name, enter the Emulex default printer server name combined with the Emulex prin

2-28 Chapter 2 Thinwire BNC Connection CAUTION: Do not break the ethernet connection while LAN is active. 1) If connecting to the middle of a ca

Printer Server Installation 2-29 Peripheral Connections Parallel Port The parallel port provides a female DB25 connector and supports the followin

Table of Contents iii NETQUE TOKEN RING...2-39 REFERENCE NUMBERS .

2-30 Chapter 2 NOTE: Serial cable between the printer server and the peripheral device or console terminal should not exceed 50 feet (15.24 meter

Printer Server Installation 2-31 Display Lights (LEDs) 1) When the printer server is powered up, the green POWER LED will illuminate. 2) Wait 15

2-32 Chapter 2 Print Test Page The test page is a helpful tool that can be used to verify the connection between the printer server and the print

Printer Server Installation 2-33 Reset to Factory Defaults Before resetting to factory defaults, we recommend that you print out a configuration p

2-34 Chapter 2 Factory Default Configuration Parameter Default Setting Passwords system (privilege mode) access (remote login) Printer server nam

Printer Server Installation 2-35 Printer Server Specifications Parameter Range Ethernet Compatibility IEEE 802.3, Ethernet Type 2 10base2, Thinw

2-36 Chapter 2 Optional Power Supply Specifications Customers providing their own power supply will need to meet these specifications. This will

Printer Server Installation 2-37 Declaration of Conformity This Declaration identifies the product, manufacturer’s name and address, and applicab

2-38 Chapter 2 What’s Next? After successfully installing your Emulex printer server, you must configure the network operating system (NOS). Refe

Printer Server Installation 2-39 NETQue Token Ring Reference Numbers It is important that you make a note of the printer server’s unique ethernet

Table of Contents iv BINDERY EMULATION MODE ... 3-9 Create the Print Queue ...

2-40 Chapter 2 NOTE: We suggest you use the default printer server name when installing the printer server for the first time. To determine the

Printer Server Installation 2-41 LAN Connections & Cabling The printer server may be connected to the network with one of these cables. • Uns

2-42 Chapter 2 Shielded Twisted-Pair STP Connection 1) Connect one end of the STP cable to the printer server STP port. See appendix for STP pino

Printer Server Installation 2-43 Serial Port Connect to the serial port with a null modem cable. The serial port provides a male DB9 connector an

2-44 Chapter 2 5) Plug the power supply transformer into an AC power outlet. The printer server will power up and go through a self-test. Figur

Printer Server Installation 2-45 Display Lights (LEDs) 1) When the printer server is powered up, the green POWER LED will illuminate. 2) Wait 15

2-46 Chapter 2 Print Test Pagearameters The test page is a helpful tool that can be used to verify the connection between the printer server and

Printer Server Installation 2-47 Reset to Factory Defaults Before resetting to factory defaults, we recommend that you print out a configuration p

2-48 Chapter 2 Reset Using Software Command 1) Obtain privileged status. 2) Enter this command: > Server>> initialize server delay dela

Printer Server Installation 2-49 Factory Default Configuration Parameter Default Setting Passwords system (privilege mode) access (remote login)

Table of Contents v CONFIGURE THE PRINT QUEUE ...4-10 Configure for BSD Hosts...

2-50 Chapter 2 Printer Server Specifications Parameter Range Ethernet Compatibility IEEE 802.5 IBM Token Ring Unshielded Twisted-Pair (UTP) RJ45

Printer Server Installation 2-51 Optional Power Supply Specifications Customers providing their own power supply will need to meet these specifica

2-52 Chapter 2 Declaration of Conformity This equipment complies with CISPR22/EN55022 Class A. WARNING: This is a class A product. In a domestic

Printer Server Installation 2-53 What’s Next? After successfully installing your Emulex printer server, you must configure the network operating s

Contacting Emulex Chapter 10 TECHNICAL ASSISTANCE...10-1

Contacting Emulex 10-1 Technical Assistance If you experience problems and cannot resolve them, contact Emulex Technical Support. Prior to Your Call

10-2 Chapter 10 Placing the Call After you gather the requested information, contact Emulex at one of these sites. Domestic Emulex (USA) Technical S

Contacting Emulex 10-3 24 - Hour Support Technical Support within the USA is available 24 hours a day. After normal working hours, dial one of the f

10-4 Chapter 10 3) Set the software to dial one of these domestic or European numbers: − Domestic: (714) 662-1445 Auto rollover will be activated i

Contacting Emulex 10-5 Internet The Emulex BBS has Internet access via Anonymous ftp, an Internet service that allows connection to a remote host wit

Table of Contents vi WHAT’S NEXT?... 6-7 CONFIGURE NOS...

10-6 Chapter 10 NOTE: The file EMULEX.LST in the EVERYONE directory describes the files located in each directory. EmuFax EmuFax is an automated doc

Novell NetWare Chapter 3 REQUIREMENTS...

3-2 Chapter 3 RESTART THE PRINTER SERVER...3-13 286 NON-DEDICATED SE

Novell NetWare 3-1 You may configure in the Novell NetWare environment using either pconsole (as explained in this chapter) or the NET wizard pr

3-2 Chapter 3 Before Installation We recommend writing down the following parameters from the Setup Section in Chapter 2. Refer to them during the

Novell NetWare 3-3 Configure as PSERVER - NetWare 1.2 to 3.12 Prior to using the Emulex printer server as a Novell NetWare PSERVER, the user must

3-4 Chapter 3 Add the Printer Server From the AVAILABLE OPTIONS menu: 1) Select PRINT SERVER INFORMATION. 2) Press INSERT. 3) Enter the Emulex de

Novell NetWare 3-5 Restart the Printer Server The following procedure allows the printer server to read the new configuration in the file server’s

3-6 Chapter 3 NDS Mode Requirements • Printer objects must be in the same context as the Pserver object which references the printer objects. • De

Novell NetWare 3-7 Add the Printer Server From the AVAILABLE OPTIONS menu: 1) Select CHANGE CONTEXT. 2) Enter the context name. This name defin

Table of Contents vii TEST PRINTER...8-12 CHANGE OR DELETE PR

3-8 Chapter 3 5) Press INSERT. This will display a list of available print queues. 6) Select a print queue from the list. 7) Press ESC to save th

Novell NetWare 3-9 Bindery Emulation Mode If multiple file servers use the printer server, the printer server must be defined consistently on each

3-10 Chapter 3 Add the Printer From the PRINTER SERVER INFORMATION menu: 1) Select PRINTERS. 2) Press INSERT. 3) Enter the Emulex default server

Novell NetWare 3-11 Configure as RPRINTER Prior to using the Emulex printer server as a Novell NetWare remote printer, the user must first create

3-12 Chapter 3 4) Press ENTER. 5) Select the printer server name. 6) Select PRINT SERVER CONFIGURATION. 7) Select PRINTER CONFIGURATION. 8) Sel

Novell NetWare 3-13 Restart the Printer Server The printer server must be stopped and restarted to enable the new configuration. Use one of the

3-14 Chapter 3 Logging into the Printer Server You can log into the printer server remotely from a Novell workstation using the TES terminal emulati

Novell NetWare 3-15 > c:> a:\install a: c: This command installs the files from drive A to C:\tes-krmt. NOTE: TES must be loaded after Net

3-16 Chapter 3 12) At Password>, enter system: > Password> system where system is the default privileged password which does not echo back.

Novell NetWare 3-17 5) At Server>, enter su: > Server> su This gives you supervisor status. 6) At Password>, enter system: > Pa