Emulex LightPulse LPe1105-M4 HBA Guide d'installation Page 133
- Page / 182
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring a VNX series or CLARiiON boot device
133
Configuring a Boot Device on an EMC Storage Array
◆ SCSI hard disks are allowed in SAN boot configurations.
However, the BIOS for the disk's SCSI adapters must be disabled.
Any SCSI disks attached to the host should be disconnected
during the operating system installation.
◆ For servers with SCSI CD-ROM drives, ensure that the BIOS is
enabled on the SCSI channel that includes the CD-ROM. Disable
the BIOS on any other integrated SCSI channels.
◆ For servers with IDE CD-ROM drivers, disable the BIOS on the
server's integrated SCSI adapter(s). The SCSI BIOS is not required
to boot from the CD-ROM.
◆ Disable the BIOS on any other HBAs in the system other than the
Emulex HBA designated for booting.
Configuring the Emulex boot BIOS for SAN boot
After the boot BIOS is installed and enabled, it must be configured for
use for booting from the SAN. The following procedure describes
how to configure the boot BIOS:
1. Connect the VNX series or CLARiiON SP Fibre Channel port to
the adapter in the lowest-numbered PCI slot in the server. For
example, if there are three adapters in the system in slots 2, 4, and
5, connect the cable to the adapter in slot 2. Do not connect cables
to the other adapters at this time.
2. Boot the server, and press ALT-E when the Emulex banner
appears.
3. The first screen of the BIOS setup utility contains a list of all the
adapters with the boot BIOS installed. Select Option 1 from the
list, and press ENTER.
4. On the next screen, select Option 2 - Configure This Adapter's
Parameters, and press ENTER.
5. Select Option 4 - Topology and press ENTER.
6. Select Option 1 - Auto Topology: Loop First (default) and press
ENTER.
7. Press ESC to return to the Parameters menu.
Select Option 1 - Enable/Disable Boot BIOS, and press ENTER.
8. If the BIOS is listed as Disabled, select 1 to enable it, and press
ENTER.
- -508-435-1000 1
- Contents 3
- Emulex Driver 4
- Chapter 8 Additional Notes 6
- ◆ Linux operating environment 9
- ◆ Emulex adapters and drivers 9
- Courier italic 11
- Introduction 13
- Purpose of this document 14
- Host connectivity 14
- Boot device support 15
- Installation Steps 19
- Linux distribution of choice 21
- Summary of installation steps 22
- Installing the adapter 24
- Adapter edge connectors 28
- PCI Express slots 29
- PCI Express slots aligned 29
- Installing and 31
- Configuring the BIOS 31
- Settings 31
- LP1102 Emulex banner 32
- Updating the boot BIOS 33
- LP6DUTIL.EXE) 37
- LP6DUTIL.EXE program file 37
- 7.x driver) 38
- Installing and 43
- Configuring the Linux 43
- Host with the Emulex 43
- SLES 9, SLES 10, and SLES 11 52
- /sys filesystem 58
- ...Restoring 83
- Cleaning up 86
- ./hbanyware 86
- * If PEMC owerPath 88
- ◆ Miracle Linux v4.0 92
- ◆ RedFlag DC Server 5.0 92
- 4 and RHEL 5” on page 91 93
- Updating the Adapter 97
- Firmware 97
- FCoE adapters 102
- Connecting to the 109
- Planning procedure 110
- Enabling persistent binding 111
- Connecting to the Storage 112
- Editing /etc/modules.conf 114
- Network Settings window 117
- Configuring a Boot 121
- Device on an EMC 121
- Storage Array 121
- Limitations 124
- /dev/sda by the Linux 125
- Preparing the host 128
- CLARiiON 136
- Emulex v7.x-Series driver 138
- Application Kit 141
- Do you have a driver disk 142
- Driver Update OK 143
- Upgrading the Linux kernel 145
- Additional Notes 147
- Rebooting the host 151
- HPQ server-specific note 155
- Block device file names 157
- Red Hat distributions 158
- SuSE distributions 158
- PowerPath examples 159
- Character device file names 159
- Echoing the /proc filesystem 163
- Rescanning the SCSI bus 164
- Special Instructions 167
- For example: 170
- 3. Reboot the host 170
- • For SuSE distributions use: 173
- Example: 173
- 4. Reboot the host 173
- 2.1 Intel Itanium systems 178
- 3.0 Intel Itanium systems 179
Produits connexes et manuels pour Logiciel Emulex LightPulse LPe1105-M4 HBA
Logiciel Emulex LP21000 Manuel d'utilisateur
(274 pages)
(274 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels